Removal and installation of a poliklinovy belt. Audi A4 (from 2001 to 2005 release)
Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. General information
2.2. Predvaritlny checks
2.3. Mekhanichsky part (petrol engines 2,0l)
2.3.1. Removal of the engine
2.3.2. Removal and installation of a poliklinovy belt
2.3.3. Removal and installation of a belt pulley of the crankshaft
2.3.4. Removal and installation of a gear belt
2.3.5. Removal and installation of a sealing flange and flywheel / the conducted disk
2.3.6. Replacement of manzhetny consolidation of the crankshaft on the party of a belt pulley
2.3.7. Removal and installation of a forward sealing flange
2.3.8. Removal and installation of a two-mass flywheel
2.3.9. Removal and installation of the conducted disk
2.3.10. Removal and installation of a bent shaft
2.3.11. Removal and a press fitting of the needle bearing in the crankshaft
2.3.12. Removal and installation of an asterisk
2.3.13. Dismantling and assembly of pistons and rods
2.3.14. Head of the block of cylinders
2.3.15. Removal and installation of the valve of 1 system of change of phases of gas distribution
2.3.16. Removal and installation of a cover of a head of the block of cylinders
2.3.17. Removal of a head of the block of cylinders
2.3.18. Installation of a head of the block of cylinders
2.3.19. Check of a compression
2.3.20. Repair of the valvate mechanism
2.3.21. Removal and installation of the phase shifter
2.3.22. Removal and installation of cam-shafts
2.3.23. Replacement of oil scraper caps (at the established head of the block of cylinders)
2.3.24. Check of the directing plugs of valves
2.3.25. Replacement of manzhetny consolidation of a final cam-shaft
2.4. Lubrication system
2.5. Cooling system
2.6. System of injection
2.7. System of production of the fulfilled gases
2.8. Mechanical part (petrol engines 3,0; 3,2 l)
2.9. Mechanical part (petrol engines of 4,2 l)
2.10. Mechanical part (diesel engines of 2,0 l)
2.11. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 







2-3-2-snyatie-i-ustanovka-poliklinovogo-remnya.html

2.3.2. Removal and installation of a poliklinovy belt

Fig. 2.97. Contour of a poliklinovy belt: 1 – damper of tortional fluctuations; 2 – tension damper of a poliklinovy belt; 3 – poliklinovy belt; 4 – generator; 5 – pump of the hydraulic booster; 6 – by-pass roller; 7 – conditioner compressor



NOTE
Before removal of a poliklinovy belt mark the direction of the course with chalk or a felt-tip pen. Change of the direction of the course of earlier operated belt can lead to its damage

Removal
Mark the direction of the course of a poliklinovy belt.

Fig. 2.64. Weakening of a poliklinovy belt


For weakening of a poliklinovy belt turn a tension damper on an arrow (fig. 2.64).
Record a tension element by means of a clamp.
Take off a poliklinovy belt.

Installation
Check correctness of provision of a poliklinovy belt.
Start the engine and check the belt course.

NOTE
Holding a tension element a wrench, take a stopper and weaken a tension element.


2.3.1. Removal of the engine

2.3.3. Removal and installation of a belt pulley of the crankshaft