Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. General information
2.2. Predvaritlny checks
2.3. Mekhanichsky part (petrol engines 2,0l)
2.4. Lubrication system
2.5. Cooling system
2.6. System of injection
2.6.1. Removal and installation of a turbocharger
2.6.2. Removal and installation of the vacuum block of a turbocharger
2.6.3. Adjustment of the vacuum block of a turbocharger (the turbocharger is removed)
2.6.4. The general instructions on self-diagnostics of system of injection
2.6.5. Decrease in high pressure of fuel
2.6.6. Removal and installation of a flowmeter of air
2.6.7. Removal and installation of an inlet collector with a fuel stage
2.6.8. Removal and installation of a fuel stage (Rail)
2.6.9. Removal and installation of nozzles
2.6.10. Check of pressure of fuel and residual pressure in front of the pump of high pressure
2.6.11. Check of residual pressure
2.6.12. Removal and installation of the pump of high pressure
2.6.13. Replacement of the control unit of the engine
2.6.14. Removal and installation a lambda probe in front of the catalyst
2.6.15. Removal and installation a lambda probe after the catalyst
2.6.16. The fuel tank (front-wheel cars – all models with MPI engines and 2,0 l of FSI)
2.6.17. Pumping of fuel from a tank
2.6.18. Removal and installation of the fuel tank with hinged details
2.6.19. Electric check of the fuel pump
2.6.20. Check of amount of the fuel given by the fuel pump (cars from the 4th the cylinder engine with a free admission)
2.6.21. Check of amount of the fuel given by the fuel pump (atomobil with the engine of 1,8 l Turbo)
2.6.22. Check of amount of the fuel given by the fuel pump (atomobil from the 4th the cylinder FSI engine)
2.6.23. Check of amount of the fuel given by the fuel pump (cars from 6 the cylinder MPI engine)
2.6.24. Removal and installation of knot of supply of fuel
2.6.25. Fuel tank (all-wheel drive cars till 10:04)
2.6.26. Pumping of fuel from a tank
2.6.27. Removal and installation of knot of a pedal of an accelerator with sensors of provision of a pedal
2.7. System of production of the fulfilled gases
2.8. Mechanical part (petrol engines 3,0; 3,2 l)
2.9. Mechanical part (petrol engines of 4,2 l)
2.10. Mechanical part (diesel engines of 2,0 l)
2.11. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 







2-6-21-proverka-kolichestva-podavaemogo-toplivnym-nasosom-topliva-atomobili-s.html

2.6.21. Check of amount of the fuel given by the fuel pump (atomobil with the engine of 1,8 l Turbo)

Check conditions
The minimum voltage of the accumulator is 12,5 Century.
The fuel filter has to be serviceable.
The fuel tank has to be filled not less than on 1/4.
Be convinced of that, the regulator of pressure of supply of fuel is serviceable.
Ignition is switched off.

Procedure for test
Open a cover of the block of safety locks on the left side of the dashboard.
Take out a safety lock a safety lock in a block of safety locks (the left row, the 5th big safety lock from above).
Connect remote control by means of an adaptor cable to the right plug of a socle.
Connect the tightening plug to the plug (+) joint stock bank of the car.
Turn off a cover of a jellied mouth of the fuel tank.
Limousine
Remove a luggage carrier upholstery.
Cast away if necessary the right back of a back seat forward.
Avant
Remove a back 1/3 at the left.
Remove a luggage carrier covering sideways at the left and a mud-reception bathtub.
All models

Fig. 2.241. Fastening of a cover of a deaf flange


Turn off a cover of a deaf flange (fig. 2.241).

Fig. 2.260. Plug of a deaf flange


Disconnect the return fuel-supply line 2, having pressed for this purpose the button of a clamp (fig. 2.260).
Put on the adapter the disconnected end of the return fuel-supply line and to place it in a measured vessel.

Fig. 2.276. Discharge of fuel in a measured vessel


Press the switch of remote control and hold it pressed during 15 with (fig. 2.276).

Fig. 2.275. The chart of the minimum volume of the fuel given by fuel knot


Compare the received fuel volume to the minimum volume on the chart (cm3/15 c) (fig. 2.275).

NOTE
Tension on the fuel pump at the idle engine and the working pump approximately on 2 in lower than tension of joint stock bank.

Assembly is carried out in the return sequence.
Establish a hose of the return fuel-supply line.


2.6.20. Check of amount of the fuel given by the fuel pump (cars from the 4th the cylinder engine with a free admission)

2.6.22. Check of amount of the fuel given by the fuel pump (atomobil from the 4th the cylinder FSI engine)