Replacement of an epiploon of the crankshaft on the party of a belt pulley. Audi A4 (from 2001 to 2005 release)
Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. General information
2.2. Predvaritlny checks
2.3. Mekhanichsky part (petrol engines 2,0l)
2.4. Lubrication system
2.5. Cooling system
2.6. System of injection
2.7. System of production of the fulfilled gases
2.8. Mechanical part (petrol engines 3,0; 3,2 l)
2.9. Mechanical part (petrol engines of 4,2 l)
2.9.1. Number of the engine
2.9.2. Removal and installation of a poliklinovy belt
2.9.3. Removal and installation of a damper of tortional fluctuations
2.9.4. Replacement of an epiploon of the crankshaft on the party of a belt pulley
2.9.5. Removal and installation of a two-mass flywheel
2.9.6. Removal and a press fitting of the needle bearing in a flywheel
2.9.7. Removal and installation of the conducted disk
2.9.8. Removal and installation of all covers of chains of the drive
2.9.9. Removal and installation of chains of the drive of camshafts
2.9.10. Removal and installation of the chain drive of the mechanism of management
2.9.11. Removal and installation of a chain of auxiliary drives
2.9.12. An arrangement of inserts of the main bearings on new bent shafts
2.9.13. Accessory of inserts of radical bearings, устанавливаемыхв block of cylinders
2.9.14. Removal and installation of cam-shafts
2.9.15. Removal and installation of roller levers
2.9.16. Replacement of oil scraper caps
2.9.17. Check of adjustment of phases of gas distribution
2.10. Mechanical part (diesel engines of 2,0 l)
2.11. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 







2-9-4-zamena-salnika-kolenvala-na-storone-remennogo-shkiva.html

2.9.4. Replacement of an epiploon of the crankshaft on the party of a belt pulley

Removal
Bring a radiator frame into service situation.
Remove a damper of tortional fluctuations.
Establish an internal part of a stripper of manzhetny consolidation aflush with an external part and record a bolt with a nakatka.

Fig. 2.397. Installation of a stripper of manzhetny consolidations


Grease a carving head of a stripper of manzhetny consolidations with engine oil, establish and, having strongly pressed, twist it as it is possible more deeply in manzhetny consolidation (fig. 2.397).
Weaken a bolt with a nakatka and to turn an internal part of a stripper against the crankshaft until the epiploon is extended.
Clamp a stripper flat places in a vice.
Remove an epiploon with pincers.

Installation
Clear a working and adjacent surface.

Fig. 2.398. Installation of manzhetny consolidation on a fork


Place the auxiliary adjusting device on the got plug and pull manzhetny consolidation 1 over the got plug (fig. 2.398).
Remove an auxiliary mandrel.

Fig. 2.399. Installation of manzhetny consolidation on a privalochny surface on the engine


Get the got plug on a bent shaft and pull manzhetny consolidation 1 over a privalochny surface on the engine (fig. 2.399).

NOTE
Leave the adjusting plug on the crankshaft for a press fitting.

Install the expansion plug with mm M8x55 bolts on a bent shaft.
Screw at first bolts by effort of a hand.

Fig. 2.400. Press fitting of manzhetny consolidation


Tighten bolts alternately on 1/2 turns to press a sealing ring to the emphasis (fig. 2.400).
Further installation is carried out in the return sequence, at the same time it is necessary observe the following:
– establish a damper of tortional fluctuations.
– establish a radiator frame by means of Ustanovkany details.
– lower an emphasis against a provorachivaniye at the expense of a body weight on the rubber buffer and fasten bolts.
– establish a casing of a front bumper.
– check adjustment of headlights.

Inhaling moment
Emphasis of a support of jet thirst for a radiator frame: 28 N · m.


2.9.3. Removal and installation of a damper of tortional fluctuations

2.9.5. Removal and installation of a two-mass flywheel