Removal and installation of a damper of tortional fluctuations. Audi A4 (from 2001 to 2005 release)
Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. General information
2.2. Predvaritlny checks
2.3. Mekhanichsky part (petrol engines 2,0l)
2.4. Lubrication system
2.5. Cooling system
2.6. System of injection
2.7. System of production of the fulfilled gases
2.8. Mechanical part (petrol engines 3,0; 3,2 l)
2.9. Mechanical part (petrol engines of 4,2 l)
2.9.1. Number of the engine
2.9.2. Removal and installation of a poliklinovy belt
2.9.3. Removal and installation of a damper of tortional fluctuations
2.9.4. Replacement of an epiploon of the crankshaft on the party of a belt pulley
2.9.5. Removal and installation of a two-mass flywheel
2.9.6. Removal and a press fitting of the needle bearing in a flywheel
2.9.7. Removal and installation of the conducted disk
2.9.8. Removal and installation of all covers of chains of the drive
2.9.9. Removal and installation of chains of the drive of camshafts
2.9.10. Removal and installation of the chain drive of the mechanism of management
2.9.11. Removal and installation of a chain of auxiliary drives
2.9.12. An arrangement of inserts of the main bearings on new bent shafts
2.9.13. Accessory of inserts of radical bearings, устанавливаемыхв block of cylinders
2.9.14. Removal and installation of cam-shafts
2.9.15. Removal and installation of roller levers
2.9.16. Replacement of oil scraper caps
2.9.17. Check of adjustment of phases of gas distribution
2.10. Mechanical part (diesel engines of 2,0 l)
2.11. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 







2-9-3-snyatie-i-ustanovka-dempfera-krutilnykh-kolebanijj.html

2.9.3. Removal and installation of a damper of tortional fluctuations

Remove
Bring a radiator frame into service situation.

NOTE
For an otvorachivaniye and an inhaling of a damper of fluctuations to hold with a cap key a belt for the central nut of a belt pulley of the generator.


Fig. 2.396. Fixing bolts of a quencher of tortional fluctuations


On several turns weaken 8 fixing bolts of a quencher of tortional fluctuations (fig. 2.396).

NOTE
Before removal of a poliklinovy belt mark the direction of the course with chalk or a felt-tip pen. Change of the direction of the course of earlier operated belt can lead to its damage.

Turn off the tension screw and take off poliklinovy a belt.
Remove a damper of tortional fluctuations.

Installation
Establish in the return sequence.

NOTE
Replace bolts which dragged on with dovoroty.
The quencher of tortional fluctuations is established only in one situation – pay attention to unloading plugs.

Establish a poliklinovy belt.
Establish a radiator frame by means of Ustanovkany details.
Lower an emphasis against a provorachivaniye at the expense of a body weight on the rubber buffer and fasten bolts.
Establish a casing of a front bumper.
Check adjustment of headlights.

Inhaling moments
Damper of tortional fluctuations to the crankshaft: 22 N · m +45 ° *.
Emphasis of a support of jet thirst for a radiator frame **: 28 N · m.
* 45 ° there correspond 1/8 turns.
** Replace bolts.


2.9.2. Removal and installation of a poliklinovy belt

2.9.4. Replacement of an epiploon of the crankshaft on the party of a belt pulley