Removal and press fitting of the needle bearing of a two-mass flywheel (cars from the manual transmission). Audi A4 (from 2001 to 2005 release)
Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. General information
2.2. Predvaritlny checks
2.3. Mekhanichsky part (petrol engines 2,0l)
2.4. Lubrication system
2.5. Cooling system
2.6. System of injection
2.7. System of production of the fulfilled gases
2.8. Mechanical part (petrol engines 3,0; 3,2 l)
2.8.1. Number of the engine
2.8.2. Removal and installation of a poliklinovy belt
2.8.3. Removal and installation of a damper of tortional fluctuations
2.8.4. Removal and installation of a forward sealing flange of the crankshaft with a crankshaft epiploon
2.8.5. Removal and installation of a two-mass flywheel (cars from the manual transmission)
2.8.6. Removal and a press fitting of the needle bearing of a two-mass flywheel (cars from the manual transmission)
2.8.7. Removal and installation of the conducted disk (cars with the automatic transmission)
2.8.8. Replacement of an epiploon of the crankshaft from the chain drive
2.8.9. Removal and installation of the left and right covers of driving chains
2.8.10. Removal and installation of the lower cover of a driving chain
2.8.11. Camshaft drive
2.8.12. Removal of the chain drive from cam-shafts, removal and installation of a natyazhitel of a chain
2.8.13. Removal and installation of a chain of the drive of the oil pump and balancer shaft
2.8.14. Removal and installation of the balancer shaft
2.8.15. Removal and installation of a bent shaft
2.8.16. Conrod and piston group
2.8.17. Check of a radial gap of rods
2.8.18. Check of a compression
2.8.19. Removal and installation of cam-shafts
2.8.20. Replacement of oil scraper caps
2.8.21. Check of basic elements with hydrocompensators
2.8.22. Check of the directing plugs of valves
2.9. Mechanical part (petrol engines of 4,2 l)
2.10. Mechanical part (diesel engines of 2,0 l)
2.11. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 







2-8-6-snyatie-i-zapressovka-igolchatogo-podshipnika-dvukhmassovogo-makhovika-avtomobili.html

2.8.6. Removal and a press fitting of the needle bearing of a two-mass flywheel (cars from the manual transmission)

Operating procedure
Remove the check point.
Remove press a clutch plate.

Fig. 2.313. Measurement of depth of a press fitting of the needle bearing in a two-mass flywheel


Measure and write down depth of a press fitting (size x) of the needle bearing in a two-mass flywheel for further assembly (fig. 2.313).

Fig. 2.314. Extraction of the needle bearing


Take the needle bearing by means of an internal stripper and a countersupport (fig. 2.314).

NOTE
The plastic ring in a two-mass flywheel is susceptible to blows. At damage of a plastic ring – replace a two-mass flywheel.


Fig. 2.315. Press fitting of the needle bearing


Press the needle bearing a mandrel in a two-mass flywheel (fig. 2.315).
Press the needle bearing a reverse side of the aligning mandrel before achievement of previously measured landing depth.
Then check depth of a press fitting (size x) of the needle bearing in a two-mass flywheel (fig. 2.313).
Establish press a clutch plate.
Establish the check point.


2.8.5. Removal and installation of a two-mass flywheel (cars from the manual transmission)

2.8.7. Removal and installation of the conducted disk (cars with the automatic transmission)