Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. General information
2.2. Predvaritlny checks
2.3. Mekhanichsky part (petrol engines 2,0l)
2.4. Lubrication system
2.5. Cooling system
2.6. System of injection
2.7. System of production of the fulfilled gases
2.8. Mechanical part (petrol engines 3,0; 3,2 l)
2.9. Mechanical part (petrol engines of 4,2 l)
2.10. Mechanical part (diesel engines of 2,0 l)
2.10.1. Number of the engine
2.10.2. Glow plugs
2.10.3. Removal and installation of a poliklinovy belt
2.10.4. Removal and installation of a tension element of a poliklinovy belt
2.10.5. Removal and installation of a quencher of tortional fluctuations
2.10.6. Removal and installation of an arm of additional units
2.10.7. Removal and installation of a gear belt
2.10.8. Correction of phases of gas distribution
2.10.9. Provorachivaniye of the crankshaft to VMT
2.10.10. Sealing flanges and two-mass flywheel / flywheel
2.10.11. Removal and installation of a flywheel, cars from multitronic
2.10.12. Conrod and piston group
2.10.13. Removal and installation of a cover of a head of the block of cylinders
2.10.14. Repair of the valvate mechanism
2.10.15. Removal and installation of cam-shafts
2.10.16. Removal and installation of roller levers
2.10.17. Replacement of oil scraper caps
2.10.18. Check of hydraulic pushers
2.11. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 




buy generic cialis online


2-10-5-snyatie-i-ustanovka-gasitelya-krutilnykh-kolebanijj.html

2.10.5. Removal and installation of a quencher of tortional fluctuations

Removal
Bring a radiator frame into service situation.
Remove an engine casing.
Take off poliklinovy a belt.
Wring out a cover of a quencher of tortional fluctuations.

Fig. 2.481. Untwisting of a quencher of tortional fluctuations


Turn off a quencher of tortional fluctuations, holding the central bolt a cap wrench (fig. 2.481).

Installation
Installation is made in the return sequence.
Establish a quencher of tortional fluctuations with new original bolts.

Fig. 2.482. Adjusting provision of a quencher of tortional fluctuations


Installation is possible only in one situation: the opening of a quencher of tortional fluctuations has to be over a ledge of a gear wheel of a gear belt (fig. 2.482).
Establish poliklinovy a belt.
Establish a radiator frame with hinged elements.
Lower an emphasis of a forward support at the expense of a body weight on the rubber buffer and tighten nuts.
Establish an overlay of a front bumper.

Inhaling moments
Quencher of tortional fluctuations to коленвалу*: 10 N · m +90 ° **.
Emphasis of a forward support to a radiator frame: 28 N · m.
Hose collars, width are 9 mm: 3 N · m.
Hose collars, width are 13 mm: 5,5 N · m.
* Replace bolts.
** 90 ° correspond to one quarter of a whole revolution.


2.10.4. Removal and installation of a tension element of a poliklinovy belt

2.10.6. Removal and installation of an arm of additional units