Removal and installation of a frame of glass and window regulator of a back door. Audi A4 (from 2001 to 2005 release)
Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Hinged elements of a body
8.2. Doors, locks of doors and hatch of a roof
8.2.1. Removal and installation of a frame of glass and window regulator of a forward door
8.2.2. Removal and installation of the electric motor of a window regulator
8.2.3. Adjustment of a forward door
8.2.4. Removal of the handle of a door
8.2.5. Removal of the lock of a door
8.2.6. Repair of the central lock
8.2.7. Removal and installation of a frame of glass and window regulator of a back door
8.2.8. Adjustment of a back door
8.2.9. Removal and installation of a wind-shelter guard of the hatch of a roof
8.2.10. Removal and installation of a sun-protection blind
8.2.11. Removal and installation of a slip
8.2.12. Adjustment of a cover of the lifting and movable hatch
8.2.13. Replacement of a sealant of the panel of the hatch
8.2.14. Cleaning of drainage hoses
8.3. Body glazing
9. Schemes of electric equipment
 







8-2-7-snyatie-i-ustanovka-ramki-stekla-i-steklopodemnika-zadnejj-dveri.html

8.2.7. Removal and installation of a frame of glass and window regulator of a back door

Removal
Remove a door upholstery.
Remove the window regulator electric motor a manual window regulator.
Disconnect shtekerny sockets.

Fig. 8.66. The frame flew down also a window regulator: 1 – the frame flew down


Turn off bolts of 7 and 8 (fig. 8.66).
Turn off bolts 3, 4, 6 and 10 and to take a glass frame with a window regulator from a door up (fig. 8.66).

Installation
Insert a frame and a window regulator into a door from above.
Frame the top half of a profile of consolidation on a door of glass.
Slightly wrap fixing screws 4 ahead and behind.
In conclusion slightly wrap bolts in the sequence of 3, 10, 8 (fig. 8.66).
Screw by hand adjusting bolts with a fillet of 4 (fig. 8.66).
Slightly press the top part of a frame of glass 1 in the direction inside.
Tighten bolts the 3 and 10 moment of 32 N · m (fig. 8.66).
Tighten adjusting bolts with a fillet the 4th moment of 32 N · m.
Tighten a bolt the 8th moment of 10 N · m.
Tighten the fixing screw (shooter) in a glass frame the moment of 32 N · m.
Insert the lower half of a sealant of a door into an internal wall of a door.
Fix a window regulator holder by a bolt 7 on an internal wall of a door.
Press carving pins of a drum of a window regulator until they are not recorded in an internal wall of a door.

Removal and installation of the electric motor of a window regulator

Fig. 8.58. Electric motor of a window regulator of a forward door


For removal turn off bolts 2 and remove the electric motor of a window regulator (fig. 8.58).
Installation of the electric motor of a window regulator is carried out in the return sequence.

Removal and installation of a manual window regulator

Fig. 8.67. Manual window regulator


Turn off bolts 2 and remove a manual window regulator from the inside of a wall of a door (fig. 8.67).
Installation of a manual window regulator is carried out in the return sequence.


8.2.6. Repair of the central lock

8.2.8. Adjustment of a back door