Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Hinged elements of a body
8.2. Doors, locks of doors and hatch of a roof
8.2.1. Removal and installation of a frame of glass and window regulator of a forward door
8.2.2. Removal and installation of the electric motor of a window regulator
8.2.3. Adjustment of a forward door
8.2.4. Removal of the handle of a door
8.2.5. Removal of the lock of a door
8.2.6. Repair of the central lock
8.2.7. Removal and installation of a frame of glass and window regulator of a back door
8.2.8. Adjustment of a back door
8.2.9. Removal and installation of a wind-shelter guard of the hatch of a roof
8.2.10. Removal and installation of a sun-protection blind
8.2.11. Removal and installation of a slip
8.2.12. Adjustment of a cover of the lifting and movable hatch
8.2.13. Replacement of a sealant of the panel of the hatch
8.2.14. Cleaning of drainage hoses
8.3. Body glazing
9. Schemes of electric equipment
 




Сдать медь в курганинске тут.



8-2-3-regulirovka-perednejj-dveri.html

8.2.3. Adjustment of a forward door

NOTE
For exact adjustment of a door on height, an inclination and shift use the special tool (fig. 8.59).

NOTE
The back door has to be adjusted.

Width of a joint can be checked the special tool 3371.
Size A = 3,5 mm ±0,5 mm.
Size B = 4,5 mm ±0,5 mm.

Adjustment in the longitudinal direction
Adjustment in the longitudinal direction is carried out by weakening of bolts And on a rack And the top and/or lower hinge of a door and movement of a door 2 (thanks to the increased openings in the hinge and a rack And) (fig. 8.60).

Fig. 8.60. The scheme of adjustment of a forward door in the longitudinal direction


Moment of an inhaling of 32 N · m

NOTE
In the figure 8.60 the lower hinge of a door is shown.

Adjustment concerning the center of the car

Fig. 8.61. The scheme of adjustment of a forward door in relatively center of the car


Adjustment concerning the center of the car is carried out by weakening of bolts of the hinge B above and/or below and movements of a door (grooves in the hinge) (fig. 8.61).
Moment of an inhaling of 32 N · m

NOTE
On the top and lower hinges of a door it is established on an adjusting bolt with a fillet.
Therefore, as a rule, when performing repair adjustment is not required.
If nevertheless adjustment is necessary, adjusting bolts with a fillet can be replaced with the bolts of the same size, length and durability offered in the catalog of spare parts.

NOTE
In a back part of a door adjustment is carried out by means of a lock bracket (in the direction to the center of the car).

Adjustment by means of a lock bracket
Weaken bolts 2.
And or arrows C use tags for side adjustment (fig. 8.62).

Fig. 8.62. The scheme of adjustment by means of a lock bracket


Shift a lock 1 bracket so that the door was established aflush with a contour of a body (fig. 8.62).

NOTE
Adjustment is allowed only in the direction to the center of the car, but not on height.
Use tags of an arrow B or an arrow D for adjustment on height.
At the correct adjustment the bracket of the lock has to enter the door lock on the center.

Tighten screws the moment of 25 N · m.


8.2.2. Removal and installation of the electric motor of a window regulator

8.2.4. Removal of the handle of a door