Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Hinged elements of a body
8.1.1. Removal and installation of a front bumper
8.1.2. Removal and installation of a connecting level of a roof "sedan"
8.1.3. Removal and installation of a connecting level of a roof "Avant"
8.1.4. Removal and installation of railings
8.1.5. Replacement of side protective levels
8.1.6. Removal and installation of an overlay of a threshold
8.1.7. Removal and installation of an overlay of a threshold S4
8.1.8. Removal and installation of a rear-view mirror
8.1.9. Mirror glass installation
8.1.10. Removal and installation of the electric motor of adjustment of a mirror
8.1.11. Removal and installation of a rear-view mirror of RS4
8.1.12. Removal and installation of the forward flap
8.1.13. Removal and installation of the back flap
8.1.14. Removal, installation and adjustment of a cowl (to identification number of the car 400 000)
8.1.15. Removal and installation of a gas emphasis (starting with identification number of the car 400 001)
8.1.16. Removal and installation of a gas emphasis
8.1.17. Adjustment on height of buffers
8.1.18. Removal and installation of a front grille
8.1.19. Removal and installation of a hook (up to identification number of the car 400 000)
8.1.20. Removal and installation of the lower part of the lock of a cowl
8.1.21. Adjustment of buffers of a frame
8.1.22. Removal and installation of a door of a luggage compartment
8.1.23. Removal and installation of an emphasis
8.1.24. Adjustment of a door of a luggage compartment
8.1.25. Installation of consolidation of a cover of a luggage compartment
8.1.26. Removal and installation of a cover of a luggage compartment
8.1.27. Adjustment of a cover of a luggage compartment
8.1.28. Removal and installation of the hinge of a cover of a luggage compartment
8.1.29. Removal and installation of a gas emphasis of a cover of a luggage compartment
8.1.30. Removal and installation of the cylinder of the lock of a cover of a luggage compartment
8.1.31. Removal and installation of a level of the handle of a cover of a luggage compartment
8.2. Doors, locks of doors and hatch of a roof
8.3. Body glazing
9. Schemes of electric equipment
 







8-1-5-zamena-bokovykh-zashhitnykh-planok.html

8.1.5. Replacement of side protective levels

NOTE
Protective levels cannot be removed without damage.


Fig. 8.14. Removal of protective levels


For removal of a protective level 1 and 2 heat by means of the hair dryer and remove from a door (fig. 8.14).
On the surface of glue connection there should not be a dust and oil.
Clear an external covering flushing gasoline, then process a silicone eliminator, and at the end wipe dry.
It is allowed to paste protective levels only at the room temperature.
For this purpose, not less than in two hours prior to processing, bring temperature of the car and protective levels to room.
After removal of a protective film the level needs to be pasted within 90 min.
Remove a protective film 3 from a bilateral adhesive tape 4 just before installation (fig. 8.14).
Establish the pasted protective level ahead and paste in the direction back.
Heat a protective level by means of the hair dryer approximately to 40 °C of C and strongly press or a prikatayta a roller.
After gluing of a slip the car has to be at the room temperature during 4 h.


8.1.4. Removal and installation of railings

8.1.6. Removal and installation of an overlay of a threshold