Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Hinged elements of a body
8.1.1. Removal and installation of a front bumper
8.1.2. Removal and installation of a connecting level of a roof "sedan"
8.1.3. Removal and installation of a connecting level of a roof "Avant"
8.1.4. Removal and installation of railings
8.1.5. Replacement of side protective levels
8.1.6. Removal and installation of an overlay of a threshold
8.1.7. Removal and installation of an overlay of a threshold S4
8.1.8. Removal and installation of a rear-view mirror
8.1.9. Mirror glass installation
8.1.10. Removal and installation of the electric motor of adjustment of a mirror
8.1.11. Removal and installation of a rear-view mirror of RS4
8.1.12. Removal and installation of the forward flap
8.1.13. Removal and installation of the back flap
8.1.14. Removal, installation and adjustment of a cowl (to identification number of the car 400 000)
8.1.15. Removal and installation of a gas emphasis (starting with identification number of the car 400 001)
8.1.16. Removal and installation of a gas emphasis
8.1.17. Adjustment on height of buffers
8.1.18. Removal and installation of a front grille
8.1.19. Removal and installation of a hook (up to identification number of the car 400 000)
8.1.20. Removal and installation of the lower part of the lock of a cowl
8.1.21. Adjustment of buffers of a frame
8.1.22. Removal and installation of a door of a luggage compartment
8.1.23. Removal and installation of an emphasis
8.1.24. Adjustment of a door of a luggage compartment
8.1.25. Installation of consolidation of a cover of a luggage compartment
8.1.26. Removal and installation of a cover of a luggage compartment
8.1.27. Adjustment of a cover of a luggage compartment
8.1.28. Removal and installation of the hinge of a cover of a luggage compartment
8.1.29. Removal and installation of a gas emphasis of a cover of a luggage compartment
8.1.30. Removal and installation of the cylinder of the lock of a cover of a luggage compartment
8.1.31. Removal and installation of a level of the handle of a cover of a luggage compartment
8.2. Doors, locks of doors and hatch of a roof
8.3. Body glazing
9. Schemes of electric equipment
 







8-1-11-snyatie-i-ustanovka-zerkala-zadnego-vida-rs4.html

8.1.11. Removal and installation of a rear-view mirror of RS4

Removal

Fig. 8.20. Safety tape


Before dismantle of a rear-view mirror stick a door in a zone of a mirror and edge of the case of a mirror with an adhesive tape on a textile basis, as shown in the figure 8.20.

Fig. 8.21. Mirror glass removal


Razblokruyte mirror glass the assembly lever also disconnect shtekerny sockets of heating of a mirror and automatic shielding of a mirror (fig. 8.21).

Fig. 8.19. Fastening of the electric motor of a mirror


Turn off bolts (shooters) from adjusting knot of a mirror (fig. 8.19).
At installation tighten bolts the moment of 1 N · m.
Take out the electric motor 1 of adjusting knot and disconnect the shtekerny socket 2 (fig. 8.21).
Remove an overlay of a mirror from the inside of a door.
Turn off a mirror leg kombi-bolt.
Take out an external mirror from a door and put it on a door cloth.

Fig. 8.22. Clip bolts


Turn off bolts (shooters) of a clip (fig. 8.22).

NOTE
To turn off the lower bolt, enter a face key through an opening of the central bolt of a leg of a mirror.


Fig. 8.23. Extraction of a clip


Take out a clip 1 of an opening in a leg of a mirror (fig. 8.23).
Slightly fix a mirror leg by the central bolt to a door.

Fig. 8.24. Otvorachivaniye of mirror arm bolts


Turn off bolts (4 pieces) from an arm of a mirror (fig. 8.24).

Fig. 8.25. Extraction of a set of wires from a mirror arm


Take out a set of wires 2 with plugs from an arm of a mirror of 1 (fig. 8.25).
Take out an arm of a mirror 1 of the case 2.

Fig. 8.26. Extraction of a set of wires from the mirror case


Take out a set of wires 1so plugs from the case of a mirror of 2 (fig. 8.26).
Take out a clip from the mirror case.

Fig. 8.27. Extraction of a clip



NOTE
For simplification of installation of a sealant if necessary to use soap lye.

At installation of a mirror on a door carry out consolidation 1 by means of an assembly wedge over a leg of a mirror 2.


8.1.10. Removal and installation of the electric motor of adjustment of a mirror

8.1.12. Removal and installation of the forward flap