Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical transmission
3.3. Automatic transmission
3.4. Driving mechanism
3.4.1. Repair of a power shaft on the tripoidny AAR 2000 hinge
3.4.2. Repair of the external hinge of equal angular speeds
3.4.3. Dismantling and assembly of the pro-minted tripoidny AAR 2600i or 3300i hinge
3.4.4. Dismantling of the tripoidny AAR 2600i or 3300i hinge
3.4.5. Assembly of the tripoidny AAR 2600i or 3300i hinge
3.5. Tables
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 




Смотри здесь аренда авито.



3-4-4-razborka-tripoidnogo-sharnira-aar-2600i-ili-3300i.html

3.4.4. Dismantling of the tripoidny AAR 2600i or 3300i hinge

Removal
Clamp a power shaft in a vice in horizontal position.

NOTE
Use laid on protective sponges for a vice.
You watch that the power shaft did not sustain damage.

Note the provision of an element of the hinge in relation to a power shaft
If not to mark them and at assembly to establish them not on the former place, later at operation noise can appear.
The waterproof felt-tip pen is suitable for drawing marks.
Open collars.

Fig. 3.124. Hinge boot collars


Remove a hinge boot (fig. 3.124) back.

Differences of power shafts of AAR 2600i and AAR 3300i

Fig. 3.125. Determination of the size A


Determine the size A, as shown in the figure 3.125.
The size A is 74 mm = a power shaft of AAR 2600i.
The size A is 77 mm = a power shaft of AAR 3300i.

ATTENTION
You monitor use of the corresponding special tool for these or those power shafts.


Fig. 3.126. Installation of the assembly tool


Enter for a hinge element the assembly tool for the tripoidny AAR 3300i hinge or the assembly tool for the tripoidny AAR 2600i hinge (fig. 3.126).
The directing pin 1 has to adjoin to an external element of the hinge.
Bring the assembly tool to a hinge element contact with rotation of screws with knurled heads 2.

NOTE
The element of the hinge has to be recorded in the assembly tool or without side plays.
Tighten screws 2 only by hand.


Fig. 3.127. Installation of the assembly tool for a power shaft of AAR 3300i


In the figure 3.127 the assembly tool for a power shaft of AAR 3300i is shown.
For a power shaft of AAR 2600i use the assembly tool.
By means of a percussion instrument remove a hinge element in the horizontal direction.

Fig. 3.128. Drawing a tag on the hinge: 1 – power shaft; 2 – asterisk of the tripoidny hinge


Mark with risks the assembly provision of details of 1 and 2 (fig. 3.128).
If not to mark them and at assembly to establish them not on the former place, later at operation noise can appear.
The waterproof felt-tip pen is suitable for drawing marks.
Remove lubricant with not tousled rag.

Fig. 3.129. Removal of a lock ring: 1 – pincers (usual)


Remove a lock ring (fig. 3.129).

Fig. 3.130. Vypressovka of an asterisk of the tripoidny hinge from a power shaft


Vypressuyte an asterisk of the tripoidny hinge from a power shaft (fig. 3.130).
Do not install assembly T10065/4 adaptation on a swing body.
Pull together a hinge boot
Remove lubricant from shaft teeths
Check wear of a body of swing and a guide
Pochisitite power shaft and case.


3.4.3. Dismantling and assembly of the pro-minted tripoidny AAR 2600i or 3300i hinge

3.4.5. Assembly of the tripoidny AAR 2600i or 3300i hinge