Service of Audi A4 from 2001 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
7.1. General information
7.2. Power supply system
7.3. Generator
7.4. Starter
7.4.1. Removal and installation of a starter (cars with 4-tsit. petrol engine of 1,6 l, turbocharged engine of 1,8 l, MPI of 2,0 l and FSI 2,0 l)
7.4.2. Cars from 6 cylinders the petrol MPI engine of 2,4 l and MPI of 3,0 l
7.4.3. Cars with the 6-cylinder petrol FSI engine of 3,2 l
7.4.4. Cars with the 8-cylinder MPI engine of 4,2 l – Audi S4
7.5. Relay blocks, sockets and safety locks
8. Body
9. Schemes of electric equipment
 







7-4-4-avtomobili-s-8-cilindrovym-dvigatelem-mpi-4-2-l-Audi-s4.html

7.4.4. Cars with the 8-cylinder MPI engine of 4,2 l – Audi S4

Removal
Disconnect a weight wire in the accumulator at the switched-off ignition.
Remove a back cover of a motor compartment.

Fig. 7.67. Fixing of a load gripping bracket


Fix a load gripping bracket on the right back eyes of the engine (fig. 7.67).

NOTE
Do not take a position 1 into account.


Fig. 7.68. Installation traverses


Establish to a traverse on regions of threaded connections of wings (fig. 7.68).
Load gripping bracket hang traverses on the running screw.
Slightly raise the engine by means of the running screw traverses.
Remove the right forward wheel.
In cars with an autonomous heater unscrew screws of an exhaust pipe of an autonomous heater and additional heater on the noise-insulating screen.

Fig. 7.18. Fastening of the forward noise-insulating screen


Open quick disconnect clamps 1, unscrew screws 2 and remove the noise-insulating screen (fig. 7.18).

Fig. 7.69. Nuts of fastening of the regulator of the stabilizer


Turn off nuts 1–4 regulators of the stabilizer (fig. 7.69) at the left and on the right.

Fig. 7.70. Fastening of a plait of conducting on the right on the engine console


Shoot the holder of a plait of conducting on the right with consoles of the engine (arrow) (fig. 7.70).
Turn off a nut 3.

Fig. 7.71. Right console of the engine


Unscrew screws 1 and 2 and remove the right console of the engine (fig. 7.71).

Fig. 7.72. Holder of the highway of coolant


Turn off the holder highways of coolant (fig. 7.72) on the right.
Disconnect the socket 1.
Unscrew screws (shooters).

Fig. 7.73. Fastening of a support of the engine


Remove an engine support with its pillow (fig. 7.73).

Cars with the mechanical transmission
Turn off the heat-shielding screen of the right power shaft.
Turn off a wire of weight 5.
Remove electric lines 3 and 4.

Fig. 7.74. Electric lines of a starter


Turn off a nut 1 and the screw 2 (fig. 7.74).
Remove a starter.

Cars with the automatic transmission

Fig. 7.75. Heat-shielding screen of the right power shaft


Remove the heat-shielding screen of 1 right power shaft (fig. 7.75).
Turn off a wire of weight 1.
Remove electric cables 3 and 4 (fig. 7.74).
Unscrew screws 2 and 5 (fig. 7.74).
Remove a starter.

Installation
Establish in the return sequence.
Install the console of the engine and to fasten a stretcher.
Install the stabilizer.
Connect the accumulator.

Inhaling moments
Component: N · m     
Starter to the transmission: 65 N · m.
The B+ plug to a starter: 16 N · m.
Weight wire to a starter: 22 N · m.
Engine support to the block цилиндров*: 42 N · m.
The heat-shielding screen of a power shaft to the transmission: 23 N · m.
* To establish with use of a carving varnish; carving varnish.


7.4.3. Cars with the 6-cylinder petrol FSI engine of 3,2 l

7.5. Relay blocks, sockets and safety locks