1.5.7. Management of the menu of an autonomous heater

The RESET button and the switch of functions of the handle of a screen wiper it is possible to cause indication of the menu, to read out data and to carry out control.

Fig. 1.138. Governing bodies

Press the RESET B button so often, indication of the menu (fig. 1.138) will not appear yet.

For management of indication of the menu press the switch of functions A. Switching is carried out similar to indication (forward/back).

Press the RESET button.

Pressing of the switch of functions makes selection of indication of the menu / possibly change of settings. The chosen parameters are allocated with a red background.

Pressing of the RESET button the chosen function / joins the set parameters are confirmed. The chosen functions are marked with "tick".

Management of an autonomous heater / fan is carried out by the RESET button and the switch of functions located on the screen wiper handle.

Programming and control is exercised through the modes of setup of the display of a combination of devices.

Press the RESET button. There is an initial menu.

Pressing of the switch of functions A

Fig. 1.139. FIS display of a combination of devices: the line "Standheizung" is chosen the Einstellen menu

include a funtion of "Einstellen" (control) (on a red background) (fig. 1.139).

Press the RESET button. There is a list of the menu with a possibility of control.

In the same way you will choose the Stand-heizung/-Luftung menu (an autonomous heater / fan) (fig. 1.139) from this menu.

Include urgent function by pressing of the RESET button and if necessary carry out other control

Fig. 1.140. FIS display of a combination of devices: "Timer" 3 is chosen the Heizen/Luften menu

In the mode "Incl. Motor" (only some modifications of the car) a part of heat of an autonomous heater is in addition used for warming up of the engine.

Control of an autonomous heater / fan is carried out through an information system of the driver (FIS).

You will choose the Heizen/Liiften menu (heater/fan).

Pressing of the switch of functions include the Timer 1 2 3 function.

Press the RESET button so long, one of timer figures will not begin to blink yet.

As pressing of the switch of functions you will choose the urgent timer.

Confirm with pressing of the RESET button selection of the urgent timer.

Establish by pressing of the switch of functions a line of selection on "hkh:khkh/hkh. хх".

Press the RESET button. Hour indication blinks.

Establish by pressing of the switch of functions hour indication.

Again press the RESET button. Indication of minutes blinks.

In the same way establish indication of minutes, day and month.

Press the RESET button. Now control of other functions or an exit from the menu through the Zuruck team is possible.

Mark with pressing of the switch of functions the line "Dauer хх Min" (duration хх minutes).

Press the RESET button. Indication of duration of inclusion blinks.

Establish by pressing of the switch of functions urgent duration (5-minute values ranging from 15 up to 60 min.).

Press the RESET button. Now control of other functions or an exit from the menu through the Zuruck team is possible.

After inclusion of an autonomous heater / fan through the Heizung Ein or Liiftung Ein menu or remote radio control the set parameters of duration of operation of the timer 1 are staticized.

The maximum time of preliminary programming of an autonomous heater / fan makes 30 days. At input of the value exceeding this figure, the marker of control is established for the greatest possible date.

At installation of already expired date the marker of control comes back to the display of today's date. If the entered time of hours (timer) already expired, then there is an automatic switching to tomorrow's date.

It is necessary for inclusion of an autonomous heater / fan in the set time previously include function of the timer.

After selection of the timer, installation of time and duration of inclusion include function of the timer as follows.

Mark with pressing of the switch of functions the line "Timer 1 2 3".

Establish by short-term pressing of the RESET button a tick.

Now control of other functions or an exit from the menu through the Zuruck team is possible.

The timers brought into an operating mode are presented on the display of the digital watch in the form of the following symbols:

- autonomous heater;

- independent fan.

After setup of the timer both symbols are brought to the display of the display of hours at the same time.

During the work of an autonomous heater or the fan the corresponding symbol blinks.

Also expeditious inclusion of an autonomous heater / fan is possible.

In the Heizen/Liiften menu (heater / fan) you will choose the line "Heizung Ein" (expeditious inclusion of a heater) or "Luftung Ein" (expeditious turning on of the fan).

Establish by pressing of the RESET button a tick. Thereby the autonomous heater / fan joins.

Now control of other functions or an exit from the menu through the Zuruck team is possible.

Work duration after expeditious inclusion is defined by the set control of time of the timer 1 (Timer 1).

The autonomous heater / fan can be switched off also in the manual mode.

In the Heizen/Liiften menu (heating/ventilation) you will choose the line "Heizung Ein" (expeditious inclusion of a heater) or "Luftung Ein" (expeditious turning on of the fan).

To remove with pressing of the RESET button a tick. Thereby the autonomous heater / fan is switched off.

Now control of other functions or an exit from the menu through the Zuruck team is possible.

Also radio-controlled inclusion or switching off of an autonomous heater / fan is possible.

Fig. 1.142. Remote radio control by an autonomous heater / fan

Press a key of inclusion 1, the control lamp of 2 (fig. 1.142) will not light up yet. Thereby the Heizung Ein function (expeditious inclusion of a heater) or "Liiftung Ein" (expeditious turning on of the fan) joins.

Press a key of switching off 3, the control lamp 2 will not light up yet. Thereby the Heizung Ein function (expeditious inclusion of a heater) or "Luftung Ein" (expeditious turning on of the fan) is switched off.

Fig. 1.141. Display of the digital watch

Displace back and uncover the transmitter (fig. 1.141).

Replace batteries. On batteries there is a marking for their correct installation. New batteries (1,5 B) have to meet the specification of original batteries.

Close a cover.

The operating mode (autonomous otottitel or the independent fan) decides as a result of comparison of temperature installed by appropriate authorities of management of system of heating / ventilation or the conditioner on the actual temperature in salon.

Duration of work of an autonomous heater / fan is defined by the set control of time of the timer 1 (Timer 1).

If it is necessary to include an autonomous heater / fan after the expiration of time of its work again, then it is necessary to press a key of switching off 3 and only then a key of inclusion 1 in the beginning.

At shutdown with a key 3 about three seconds the control lamp 2 transmitters burns.